SKU: HT-151384

Haltech Elite 2500 + Ford Coyote 5.0 Late Cam Solenoid Terminated Harness Kit


Calculate Shipping

Express Shipping - $AUD25.00
Express Shipping

Haltech Elite 2500 + Ford Coyote 5.0 Late Cam Solenoid Terminated Harness Kit Description

SUITS: Late Style (Late 2013 onwards) Cam Solenoid - Large 4 keyed Bosch connector. Supports DBW and quad variable cam timing. WBC1/2 CAN O2 Wideband Controller ready (Controller and sensor(s) not included) Manual transmission only.
INCLUDES: Elite 2500 ECU with DBW and Race Functions, engine harness with fuse block, firewall grommet, pre-wired HPI8 15amp high power ignition module. USB programming cable and USB software key.
NOTES: Requires modification for fitment to supercharged Cobra Jet version

• 1 to 12 cylinder engines
• 1 to 4 rotor engines
• Normally aspirated or forced induction

• Torque Management Functionality
• 8 x Fuel Injection Outputs
• 8 x Ignition Outputs
• 28 x Digital Outputs
• 10 x Analogue Voltage Inputs
• USB Laptop Communications up to 1 MB/s
• 6 x Engine Position Inputs with extensive trigger type support
• Programmable Injector Peak and Hold Currents
• OBDII Capable – Set and clear diagnostic trouble codes, view live engine data
• ESP Calibration Software – Intuitive and easy to use
• Dual CAN Bus communication for OEM and Haltech CAN Expansion
• User definable 5D Tuning – Tune by gear, Cam angle or any channel for ultimate flexibility
• Variable cam control – Independently control up to 4 camshafts Auto tune capabilities –
• Short and Long term fuel, ignition, boost and idle control learning
• Dual Channel Knock Control – with high speed digital filtering for accurate detection
• Multi-fuel Support – Support for Petrol (Gasoline),LPG, Methanol and Ethanol
• E85 Flex Fuel Ready – Direct connection to sensor.
• Closed Loop Boost Control – Multiple Modes – Tune by gear, wheel speed or time
• Closed Loop Idle Control – With learning for consistent idle stability
• Closed Loop 02 Control – Dual bank control for precise tuning
• Anti-Lag and Launch Control – Drag and Rally modes
• Data logging – Up to 40 channels of logging. Sampling rates up to 5ms
• Multi Level Engine Protection – Set limits for sensors and protect your engine
• ECU comes fully enabled, no additional charges for advanced features

• 8 x Current controlled injector drivers
• High or Low impedance injector compatible
• Programable Peak Current – 0A – 8A
• Programable Hold Current – 0A – 2A
• All spare injector outputs can be used as generic DPO’s with 1A Max output.
• 8 x Over current protected ignition drivers
• All spare ignition outputs can be used as generic DPO’s with 1A Max output.
• 5 x Over current protected low side pulsed outputs
• 1 x Dedicated engine control relay output which can control up to 6 relays simultaneously
• 2 x Over current protected hi / low side motor outputs
• Suits most OEM throttle bodies and pedals
• 1 x 4 wire stepper motor control
• Can be configured as 4 x hi / low side outputs

• 10 x Analogue Voltage Inputs
• 2 x Engine Position Inputs with extensive trigger type support
• Supports variable reluctor and digital inputs
• 3 Bar Internal MAP Sensor rated up to 200kPa of Boost (2bar/29psi)
• 2 x CAN Bus communication for Haltech CAN and Vehicle CAN Expansion
• 1 x USB Connection for Programming
• On-board Data Logging
• Fastest Sample Rate 5ms
• 2MB Internal Storage


SKU HT-151384
Brand Haltech
Shipping Weight 3.0000kg
Shipping Width 0.170m
Shipping Height 0.150m
Shipping Length 0.100m
Shipping Cubic 0.002550000m3


Be The First To Review This Product!

Help other GameOn Motorsports users shop smarter by writing reviews for products you have purchased.

Write a product review

More From This Category